This pair of6" Full-Range Ceiling LoudspeakersfromTannoyincludes two full-bandwidth, high-power handling, and high-sensitivity loudspeakers built around Tannoy's CMS 3.0 Ceiling Monitor System technology. Based on a dual-concentric point-source driver, the
This pair of6″ Full-Range Ceiling LoudspeakersfromTannoyincludes two full-bandwidth, high-power handling, and high-sensitivity loudspeakers built around Tannoy’s CMS 3.0 Ceiling Monitor System technology. Based on a dual-concentric point-source driver, the speaker delivers wide and consistent broadband directivity, intelligibility, and an accurate and linear response.
The dual-concentric driver design features Omnimagnet technology and the Torus Ogive Waveguide device, together providing consistent and controlled directivity along with improved high frequency response. Time alignment and coherence between low and high frequencies enhances performance both on- and off-axis. The baffle provides a subtle extension to the wave-guide effect for additional sonic benefits.
The loudspeaker features extra clamp extension to accommodate thicker ceiling panels, and a locking design that prevents inadvertent over-screwing. The magnetic grille attachment enables easy removal and fitting for custom painting. It utilizes a 16-Ohm driver, making it ideal for use in high-performance, low-impedance systems. A low insertion-loss 60W transformer is included, with convenient front switching for taps at 60W, 30W, and 15W, with an additional 7.5W tap for traditional constant-voltage systems.
Each speaker includes a grille, two tile support rails, and a C-ring. This pre-install model is supplied without a backcan.
Features
Specifications
| Driver | 6.5″ / 165 mm dual-concentric Omnimagnet driver |
| Low Frequency Driver | 1.75″ / 44 mm voice coil, treated multi-fiber paper pulp cone |
| High Frequency Driver | 1″ / 25 mm PEI dome |
| Frequency Range | 46 Hz to 30 kHz at -10 dB |
| System Sensitivity | 91 dB (1 W = 4 V for 16 Ohms) |
| Nominal Coverage Angle | 90 |
| Power Handling | Average: 80 W Program: 160 W Peak: 320 W |
| Recommended Amplifier Power | 160 W @ 16 Ohms |
| Nominal Impedance | 16 Ohms |
| Maximum SPL | Average: 110 dB Peak: 116 dB |
| Transformer Taps | 70 V: 60 W (83 Ohms) / 30 W (165 Ohms) / 15 W (330 Ohms) / 7.5 W (660 Ohms) / OFF & low impedance operation 100 V: 60 W (165 Ohms) / 30 W (330 Ohms) / 15 W (660 Ohms) / OFF & low impedance operation |
| Enclosure | Baffle: Reflex-loaded UL 94V-0 rated ABS Grille: Steel, with weather-resistant coating |
| Safety Features | Safety ring located at rear of enclosure for load-bearing safety bond |
| Clamping Characteristics | Security toggle clamp Clamping Range: 0.37 – 2.36″ / 1 – 6 cm Recommended Clamp Torque: 1.5 Nm |
| Mount | Separate backcan for pre-installation |
| Cable Entry | Cable clamp & squeeze connector for conduit up to 0.9″ / 22 mm |
| Conduit | Conduit Knockouts on PI Backcan: Three sets of horizontal positions 0.75″ / 19 mm, 0.87″ / 22 mm, 1.10″ / 28 mm |
| Connectors | Removable locking screw terminals with “loop thru” |
| Compliance | UL-1480, UL-2043, CE |
| Dimensions | Bezel Diameter: 10.8″ / 27.4 cm Front of Ceiling to Rear of Speaker Unit: 4.0″ / 10.1 cm Front of Accessory Backcan Bezel to Top of Safety Loop: 6.6″ / 16.9 cm Hole Cutout Diameter: 10.0″ / 25.3 cm |
| Weight | 8.1 lb / 3.7 kg |
Reviews
There are no reviews yet.